1. Devin Wakefield
  2. http://www.igert.org/profiles/5324
  3. Graduate Student
  4. Presenter’s IGERT
  5. Cornell University
  1. David Calabrese
  2. http://www.igert.org/profiles/5437
  3. Graduate Student
  4. Presenter’s IGERT
  5. Cornell University
Judges’ Queries and Presenter’s Replies
  • Icon for: Diane Cook

    Diane Cook

    Judge
    Faculty: Project PI
    May 20, 2013 | 12:11 p.m.

    What confounds, if any, exist that could cause the biosensor to report
    false positives or false negatives?

  • Icon for: David Calabrese

    David Calabrese

    Co-Presenter
    Graduate Student
    May 21, 2013 | 10:19 a.m.

    While we have not observed a false positive or negative, likely sources could be an uncharacteristically high concentration of hydrogen peroxide or a radical inhibitor already present in the sample. Depending on the sample, it may be possible that other biological material may interfere with our detection of hydrogen peroxide, but we have found nothing to suggest that that might happen.

  • Icon for: Julia Hirschberg

    Julia Hirschberg

    Judge
    Faculty: Project PI
    May 20, 2013 | 07:17 p.m.

    What are the limitations/weaknesses of your proposed technique?

  • Icon for: Devin Wakefield

    Devin Wakefield

    Lead Presenter
    May 21, 2013 | 05:57 p.m.

    Thank you Julia for your question.

    A limitation with our technique may include the fact that extended exposure to UV light is needed for optimal singlet oxygen production. We have currently tested irradiation for 60 minutes and have found that longer times can result in a signal decrease and an increase in background, possibly due to UV damage of bound antibodies. However, we have been using a wide benchtop UV light source. It may be likely that a more concentrated light source could serve to shorten this temporal requirement while minimizing any antibody damage.

    Other weaknesses are currently in the necessity of intermediates and additional reagents, like Amplex Red, for the detection of antibody produced hydrogen peroxide. For a field ready and portable biosensor device, it may be important to consider alternative detection schemes. Yet, the Amplex Red assay has been widely tested as a highly specific and sensitive measure of hydrogen peroxide concentrations. Also, the Resorufin product from this assay is very stable, allowing quantification of hydrogen peroxide in both oxidative and reductive conditions. Combining the Amplex Red assay with square wave voltammetry in our biosesnor, low hydrogen peroxide concentrations are currently detectable with high fidelity.

  • Icon for: Mostafa Bassiouni

    Mostafa Bassiouni

    Judge
    Faculty: Project Co-PI
    May 21, 2013 | 02:03 p.m.

    Does your biosensor need to be adapted or configured to work properly in different environments? For example, does the very high temperature in a remote village in Africa prevent the application of your biosensor in field disease studies? Does the small age of the patient hamper detecting infection in newly born infants?

  • Icon for: David Calabrese

    David Calabrese

    Co-Presenter
    Graduate Student
    May 22, 2013 | 09:17 a.m.

    Thank you for your question.

    Higher temperatures would promote a faster production of hydrogen peroxide while allowing for a larger signal from bound antibodies. Conversely, colder temperatures would generate a lower signal but still allow for sensitive detection. It is possible to modify the polymer brushes with other small molecules for a wider range of antibody binding. In addition, the samples would all be at a temperature of approximately 37 degrees Celcius regardless of different environments.

    Small age should not be a problem for our biosensor as it uses only a minimal sample volume to be able to detect picogram quantities of the antibody.

  • Icon for: Mary Kathryn Cowles

    Mary Kathryn Cowles

    Judge
    Faculty: Project PI
    May 21, 2013 | 04:26 p.m.

    How do the sensitivity and specificity of your biosensor compare to those of standard ELISA techniques?

  • Icon for: Devin Wakefield

    Devin Wakefield

    Lead Presenter
    May 22, 2013 | 11:03 a.m.

    Thank you Dr. Cowles for your question.
    Our biosensor compares quite favorably with standard ELISA techniques. Current tests demonstrate that hydrogen peroxide at concentrations as low as 0.33 nM can be measured. Antibodies bound at ~ 5 × 10^-12 mol/cm^2 produce over 25 × 10^-10 mol H2O2/cm^2, which translates to above 250 mM of hydrogen peroxide generated from only 10 µL of a test sample. Stated another way, these results indicate that below 3 picograms of bound antibody may be detected from a 10 µL sample, which equates to an antibody concentration of just 2 pM.
    Further, standard ELISA techniques rely on large solid supports (typically a microtiter plate) for immobilizing hapten molecules with either non-specific adsorption or by specifically capturing hapten via surface coated antibodies. Our biosensor, on the other hand, avoids challenges with these approaches by using a smaller surface area by comparison, for the presentation of sufficiently high densities of covalently attached hapten (e.g. DNP) to polymer brushes. Enhanced specificity with our biosensor comes through the capability of modifying these brushes to present a wide range of antibody haptens. Additionally, the polymer brush OEG moieties resist non-specific binding and have long-term stability as a result of their high packing characteristics. We have incubated non-specific antibodies on our DNP capped brushes and photosensitizer surfaces and have found no significant change in frequency as detected by QCM measurements, confirming that non-specific antibodies do not bind to the polymer brushes.

Presentation Discussion
  • Icon for: Angela DICiccio

    Angela DICiccio

    Graduate Student
    May 21, 2013 | 09:49 p.m.

    Really great work guys! Your video is so well depicted and explained! This seems like a really awesome system, but I’m wondering if you need to use a special method in order to get the polymer brushes to extend up from the surface with their functional groups exposed to the antibody rather than laying flat in a jumble.
    Thanks for the insightful and fun explanations!

  • Icon for: Devin Wakefield

    Devin Wakefield

    Lead Presenter
    May 21, 2013 | 10:15 p.m.

    Thanks Angie! To answer your question, the OEG moieties of the polymer brushes have high grafting densities, making them resistant to non-specific binding while offering long-term stability. More specifically, it is this dense packing of neighboring polymer chains that results in an increased entropic force to drive the brushes into a stretched, upright state.

  • robert wakefield

    Guest
    May 21, 2013 | 10:08 p.m.

    Awesome work! Best poster and video in the competition!! Hands down!!

  • Icon for: Devin Wakefield

    Devin Wakefield

    Lead Presenter
    May 21, 2013 | 10:16 p.m.

    Thanks!! :)

  • Icon for: Myisha Roberson

    Myisha Roberson

    Faculty: Project Co-PI
    May 22, 2013 | 11:37 a.m.

    Interesting work. Is your biosensor specific for a group of pathogens like influenza that you mentioned or does it sense bacteria and fungi also?

  • Icon for: Devin Wakefield

    Devin Wakefield

    Lead Presenter
    May 22, 2013 | 05:21 p.m.

    Thank you Myisha for your question.
    The development of our biosensor has been focused primarily on the detection of antibodies specific to pathogens like influenza. However, the detection of bacteria and fungi should also be feasible. Provided that our polymer brush surface can be functionalized to present the appropriate haptens (small molecules) to bind bacterial and fungal antibodies, we should be able to identify the presence of these organisms from a test sample.

  • David Bradford

    Guest
    May 22, 2013 | 08:00 p.m.

    Nice job guys. Your video was remarkably understandable. It was presented so well that even an old guy like me, who hasn’t studied high level molecular biology in such a long time, grasped the idea of what your were doing. Have you developed a prototype that will allow you to take your work out into the field to test it? To think I knew you Devin when you didn’t know anything about chemistry. Way to surpass your teacher!
    P.S. I think one of your commenters is a little biased.

  • Icon for: Devin Wakefield

    Devin Wakefield

    Lead Presenter
    May 23, 2013 | 12:43 a.m.

    Thanks Dr. Bradford!! I am so glad you enjoyed our video.
    Our biosensor at present consists only of the patterned quartz crystal microbalance (QCM) or patterned silicon chips. The QCM has allowed us to thoroughly characterize the photosensitizer / polymer brushes, determine the extent of antibody binding, and measure our limits of hydrogen peroxide detection. Having confirmed the successful performance of these aspects in the lab, we are now looking into the development of a device to enable field testing. We are considering a microfluidic platform capable of handling small fluid and reagent volumes. This system could be tuned to provide the right balance of photosensitizer and polymer brushes (covering the inside of microfluidic channels), while electrochemical features (e.g. microelectrodes) could be selectively incorporated to supply optimal hydrogen peroxide detection.
    P.S. I agree, one of my commenters has been eagerly awaiting the chance to view and comment on my work :)

  • Serena Ambrosini

    Guest
    May 23, 2013 | 01:33 a.m.

    Dear Devin congratulation for your work!
    The universabilty of this system is quite attractive!
    Since I am working on molecularly imprinted polymers (MIPs), what do you think about using MIP-based sensing layer?
    This would not be applicable to all kinds of pathogens..but it will offer an higher specificty and stability.

  • Icon for: Devin Wakefield

    Devin Wakefield

    Lead Presenter
    May 23, 2013 | 10:06 a.m.

    Thanks Serena!!
    I think the applications of MIPs for our biosensor would be quite interesting. Provided good compatibility with the patterning approach and photosensitizer, MIPs with the necessary functionality for antibody binding could be readily prepared. I would be interested to learn how the specificity and stability of MIPs compare to that of our current polymer brushes.

  • Deane Lanzano

    Guest
    May 24, 2013 | 04:43 p.m.

    Excellent !!! Keep up the GOOD work !!!!!

  • Icon for: Devin Wakefield

    Devin Wakefield

    Lead Presenter
    May 24, 2013 | 05:07 p.m.

    Thank you!! Will do!!

  • Thomas

    Guest
    May 29, 2013 | 05:54 p.m.

    Hey Devin!! That looks very cool! You figured a way to use this surprising properties of antibodies!! Great work!! Keep on the good innovation!!

    Me and Cécile are doing great, come see us in france!! We have to show you the beautiful mountains we have here

  • Icon for: Devin Wakefield

    Devin Wakefield

    Lead Presenter
    May 29, 2013 | 06:02 p.m.

    Thanks Thomas!! I am glad you found our work interesting! I will certainly have to come visit you both!

  • Further posting is closed as the event has ended.